Welcome Log in
--Price: lowest firstPrice: highest firstProduct Name: A to ZProduct Name: Z to AIn-stock first Sort by
A complete set of all nuts & bolts you need to build your Prusa Mendel 3D printer. The contents are all 8.8 BZP. We've added some extra parts, as you will most likely drop and loose some washers or screws. Thats saves you a bunch of time looking for that one lost screw. You're welcome! This kit is for...
This thickplate is used to mount the upper thickplate on, and is made out of 4mm MDF
We took the M8 threaded rod, and cut it to size, for your convencience. This kit contains: 6 M8×370mm 4 M8×294mm 3 M8×440mm 2 M8×210mm + / - 1mm.
The belts you will need to drive your Mendel. One is for the Y-axis, the other one for the X-axis. These belts are non-optimized, so your X axis is basically too long for a standard Prusa. Look for our Prusa optimized version if you want a kit that fits a Prusa! Please also note our T2.5 belt kits, which are default in...
The belts you will need to drive your Mendel. One is for the Y-axis, the other one for the X-axis. These belts are optimized in length, so your X axis fits a standard Prusa. Please also note our T2.5 belt kits, which are default in Prusa I2, and give higher printing resolution
This kit contains all steel and threaded rods you need for building a Prusa Mendel 3D printer, cut to size. Threaded rod: 6 M8×370mm 4 M8×294mm 3 M8×440mm 2 M8×210mm 1 M8×45mm and Smooth...
A complete RAMPS board, including needed endstops, pullup resistors and cabling for them. We have included Pololu A4983 stepper drivers by default, but they are optional. This kit comes unassembled, however assembly is optional. Please note assembly is made to order, we do not keep assembled stock. See below for complete contents.
Starting out with 3D printing, and just want to have everything you need for electronics? Get this kit. It contains all you need to build a Prusa Mendel or other 3D printer. By getting this kit, you indirectly support the Arduino organisation. We can assemble it all optionally, at an extra cost, so it's plug & play.
Starting out with 3D printing, and just want to have everything you need for electronics and are on a budget? Get this kit. It contains all you need to build a Prusa Mendel. With RAMPS1.3 electronics, so you can solder it yourself, but we can assemble it all optionally, at an extra cost, so it's plug & play.
Starting out with 3D printing, and just want to have a single-PCB solution? Get this kit. It contains all you need to build a Prusa Mendel or other 3D printer. We can assemble it all optionally, at an extra cost, so it's plug & play.
We took the M8 smooth rod and cut it to size, for your convenience. This kit contains: 2 8mm×420mm (X-bar) 2 8mm×405mm (Y-bar) 2 8mm×350mm (Z-bar) + / - 1mm. New lengths, to suit new (post 1nov) Prusa i2 standards!
Set of 12 8mm linear bearings
A kit to upgrade your 3D printer to T2.5 operations, adding resolution as you go. Don't forget to update your firmware!
A kit with all the nuts and bolts you need to assemble a Wade's extruder. We added some extras just to make sure you don't spend time looking for that one lost part. All is in 8.8 BZP quality! NEW: We replaced the default hobbed bolt with the Hydra hobbed bar!Check "more details" to see the exact...
The belts you will need to drive your Mendel, in T2.5 for added precision. One is for the Y-axis, the other one for the X-axis. These belts are optimized in length, so your X axis fits a standard Prusa.
The belts you will need to drive your Mendel, in T2.5 for added precision.One is for the Y-axis, the other one for the X-axis. These belts are optimized in length, so your X axis fits a standard Prusa. This kit is made especially for Prusa Mendel Iteration 2, since the design differs slightly from previous
items: 101620
No products
Shipping € 0,00 Total € 0,00
Cart Check out
» All new products
Follow us